| Raxxess/K&M
and
Ultimate |
 Config-U-Raxx
center desk
Part / Model: ACD-30-45
Overview
Config-U-Raxx angled center desk- small
Available in maple or ebony fleck with silver trim. Legs are
height adjustable for use with 12U or 14U side wings. Model
number is for center desk only. Side Wings and shelves must
be ordered separatley.
|
 |
| Raxxess/K&M
and
Ultimate |
 Config-U-Raxx
Side Wing Rack
Part / Model: ASW-20-29
ASW-20-29M shown -Logo panel not included
Angled side wings bring your rackmounted equipment closer to
your sitting position. Available as 14U rack with melamine sides
in ebony fleck or maple, 14U steel sides with silver hammertone
finish and 12U steel sides with silver hammertone finish. 1
1/8" thick melamine top surface available in ebony fleck
or maple with silver trim. Doors and shelves are sold separately.
Doors and shelves are sold separately. Must specify right or
left-hand side when ordering.
|
|
| Raxxess/K&M
and
Ultimate |
 Features
1- SCD-42B straight center desk
1 - RB-46B rack bridge
1 - UCR-B under counter rack
|
|
| Raxxess/K&M
and
Ultimate |
 Straight
center desk- small
Part / Model: SCD-36
Config-U-Raxx straight center desk- 36" wide
Available in maple or ebony fleck with silver trim. Legs are
height adjustable for use with 12U or 14U side wings. Model
number is for center desk only. Side Wings and shelves must
be ordered separatley.
|
|
| Raxxess/K&M
and
Ultimate |
 Cable
depot holds 30 cables
Part / Model: CBLD
16-gauge steel cable reorganizer keeps cabling off the floor,
out of the way and kink-free. Fourteen fingers extend to hold
up to forty cables. Maximum cable diameter is .25"
|
|
| Raxxess/K&M
and
Ultimate |
 Features
1 - CRND-B corner desk
2 - SSW-22B side wing racks
1 - RB-46B rack bridge
2 - RB-22B rack bridges
1 - SFD studio furniture door
|
|
| Raxxess/K&M
and
Ultimate |
 Features
1 - SCD-36B center desk
2 - ssw-22/12BS side wing racks
1 - RB-36B rack bridge
2 - RB-22B rack bridges
1 - KBS-2 keyboard shelf
1 - CBS center bridge support
|
|
| Raxxess/K&M
and
Ultimate |
 Features
1 - ACD-42-56M center desk
2 - ASW-20-29M side wing racks
1 - RB-60M rack bridge
2 - RB-22M rack bridges
1 - KBS-2M
|
|
| Raxxess/K&M
and
Ultimate |
 The
Cherry Elite Racks are the ideal solution for expanding any
previous ECR installation, or when you just need great looks
and security in a rack. The ECRR racks feature the same cherry
finish and brass-plated hardware as our Elite Converta Racks.
Features include a locking smoked-plexi front door, locking
solid rear door and casters. The 20" depth allows for extra
deep equipment and plenty of room for cable management. Available
in 12, 16 and 20 racks spaces. Assembly required. |
|
| Raxxess/K&M
and
Ultimate |
 |
|
| Raxxess/K&M
and
Ultimate |
 Elite
Rack
Part / Model: ERK
Left to Right: ERK-12/8, ERK-20M, ERK-20SL
The Elite Series of fine audio racks are of knock down construction
using the highest grade of fused 3/4" melamine. They come
equipped with 11-gauge steel rack rail and the finest knockdown
furniture hardware available. The depth has been increased to
20" to accommodate all gear options. Attractive plexi front
doors and solid melamine rear door are now offered as options.
Available in ebony fleck and maple. Furniture grade casters
are standard on 12 spaces and larger.
|
|
| Raxxess/K&M
and
Ultimate |
 Part
/ Model: ERT
Providing sufficient area for housing most 32-channel mixers
along with 32 spaces of rackmount equipment, the new ERT Elite
Roll-Top rack is a secure, semiportable audio/video control
center. The locking roll-top cover prevents unauthorized users
from accessing mixer controls, while two locking pocket doors
cover the two 16-space rack bays. Locking rear doors provide
additional
security and complete the overall appearance. The heavy duty
industrial casters allow for easy indoor transport. Constructed
of 3/4" cherry melamine with brass-plated hardware, rack
ships partially assembled via common carrier.
|
|
| Raxxess/K&M
and
Ultimate |
 Elite
speaker stands Pair
ESS-42BSL: 42" tall in ebony fleck with silver trim, dual
cable management ducts, 14" platforms
ESS-42MSL: 42" tall in maple with silver trim, dual cable
management ducts, 14" platforms |
|
| Raxxess/K&M
and
Ultimate |
 Keyboard
Workstation
Part / Model: ETUDE
The Raxxess Etude is perfect as a studio keyboard workstation
or as a learning center. The frame is constructed of 1-inch
by 2-inch tubular steel side supports of 16-gauge material.
The fabricated bottom cross member is 1 1/2 inches by 6 inches.
Both the keyboard shelf and the optional printer/CPU shelf (not
pictured) that mounts to the lower portion of the frame are
adjustable in one0inch increments for up to five inches. They
each measure a generous 55" wide and 16" deep. The
55" width will support an 88-note keyboard while the contoured
upper shelf can easily accommodate audio and video monitors.
A computer keyboard shelf can be mounted to either of the two
standard shelves using the hardware provided into pre-drilled
holes.
|
|
| Raxxess/K&M
and
Ultimate |
 Acoustic
Isolation Rack
Part / Model: ISR
Recent developments in recording technology allow today's audio
professionals and enthusiasts unprecendented control over the
quality of their work. But along with the benefits provided
by these great new products comes additional noise created by
fans and hard disk drives. Raxxess now offers the IsoRaxx as
a solution to mechanical noise problems in your studio. the
IsoRaxx has all of the features you need to keep your equipment
safe and quiet, reducing fan and hard drive noise by an average
of 21dB. Features like our electrostatic filter intake (keeps
the dust bunnies out of your hard drives!), dual variable speed
fans(stays cool!), separate passage for signal, AC and computer
cables (no cable noise) are just some of the thoughtful touches
that are included in the IsoRaxx. Equipment is easily visible
through the clear lexan panel in the front door. The rear door
is mounted on removable hinges to ease equipment installation
and maintenance and is key-lockable for security. The IsoRaxx
is available in 14 or 20 rack spaces. Both sizes are available
in 30" depths, while the 14-space version is also available
in 24" depth. Constructed of 3/4" thermally fused
melamine, and available in our ebony fleck or maple finishes.
Casters are included. Ships assembled via common carrier.
|
|
| Raxxess/K&M
and
Ultimate |
 Welded
Steel Rack Enclosure
Part / Model: KAR
16-gauge cold rolled steel, welded construction
Removeable conduit knockout panels w/ D-connector holes for
mounting BNC connectors
Abundant cable passage and tie off points
Black powder coat finish
Front adjustable 11-gauge rack rail
Beveled front corners
3U panel in roof allows a variety of ventilation options
KOs in lower rear quarters for side-exiting cable
Unique cable strain-relief gulley allows for easy installation
of casters w/o caster base |
|
| Raxxess/K&M
and
Ultimate |
 Rotating
Rack System
Part / Model: ROTR
Raxxess pioneered the concept of rotating racks and continues
to lead the industry with cutting-edge rotating rack designs
to suit practically any application. Perfect for installing
in existing cabinetry or new millwork, the Raxxess Rotary Rack
system comes in sizes from eight to twenty four rack spaces.
Available in a two (ROTR-2) or four (ROTR-4) slide formats capable
of supporting 150 and 300 pounds respectively. The rack extends
a full twenty inches from its frame and is then capable of rotating
90 degrees in either direction, allowing unobstructed access
to components regardless of their depth. The system locks in
the closed position with security panel and screws provided.
Easy and effective cable mamagement system and eight-space rear
rack rail are included.
|
|
| Raxxess/K&M
and
Ultimate |
 Config-U-Raxx
Side Wing Rack
Part / Model: SSW-22
SSW-22B shown w/ optional RB-22B and SFD
Available as 14U rack with melamine sides in ebony fleck or
maple, 14U steel sides with silver hammertone finish and 12U
steel sides with silver hammertone finish. 1 1/8" thick
melamine top surface available in ebony fleck or maple with
silver trim. Doors and shelves are sold separately.
|
|
| Raxxess/K&M
and
Ultimate |
 Raxxess
makes panels for all applications. Whether you are filling space
or machining for a custom job, if you need to match the finish
on other equipment or have a particular function in mind, Raxxess
has the widest variety of panels available anywhere. All steel
panels are black powder coated in smooth or textured finishes.
All aluminum panels have a brushed black anodized finish. |
|
| Raxxess/K&M
and
Ultimate |
 6"
pop filter with goose neck
Part / Model: POMT
Overview
Steel clamp easily attaches to microphone stand; gooseneck allows
proper placement of 6" STOP-IT in front of microphones.
|
|
