Aviom Mix4

Aviom Mix4

Complete Aviom Package with 4 A-16II Mixers, Everything You Need for 4 Musicians

The Aviom Mix4 is a complete monitor mixing system for four performers.

Complete Aviom Package with 4 A-16II Mixers, Everything You Need for 4 Musicians

It easily connects to any analog console using the console's line-level outputs, direct outs, aux sends, groups, or busses.

Once the input signals are connected to the AN-16/i Input Module, run the included Cat-5e cable from the AN-16/i to the A-16D Pro A-Net Distributor which copies and splits the digital signal while at the same time adding DC power to each of its eight outputs.

Connecting a Cat-5e cable from the A-16D Pro to each A-16II Personal Mixer is all that is necessary to set up the system; the mixers get their power over the same cable that delivers the 16-channel digital signal. Plug headphones, ear buds, or an in-ear monitoring system into the Personal Mixer and you're ready to start creating custom mixes.

The system's head end includes an AN-16/i v.2 Input Module which accepts up to 16 line-level inputs. Audio is converted to digital and transmitted via A-Net®, up to 500ft/150m over Cat-5e. A dedicated audio thru is available for each input channel, allowing the AN-16/i v.2 to be seamlessly inserted into an existing audio signal path.

The 16-channel A-16II Personal Mixer allows a performer to create and save up to 16 custom mixes, and gives each performer control over channel volume, grouping, pan, stereo spread, along with master volume and tone. The system also includes an MT-1a for each Personal Mixer to allow the mixer to be mounted on any standard mic stand.

The A-16D Pro A-Net Distributor eliminates the need to daisy chain Personal Mixers, and simplifies set-up by eliminating the need to connect a power supply to each mixer. The A-16D Pro accepts one Pro16 A-Net input signal and provides nine parallel outputs, using rugged EtherCon connectors and standard Cat-5e cables. The A-16D Pro provides isolated (floating ground) DC power through the eight A-Net Outs; the ninth output is an unpowered A-Net Thru connector, designed for distributing a copy of the A-Net signal to a second A-Net Distributor or remote location.

As with all Aviom personal mixing systems, this four-mix package can be expanded as needed to include more Personal Mixers at any time.

Mix4 Technical Specifications


AN-16/i v.2 Input Module

Audio Inputs Inputs TRS Thru Analog to Digital Conversion Frequency Response A- Net In A-Net Out Gain Settings Channel LED Indicators Line Inputs Metering Stereo Operation Maximum Input Level Input Impedance Freq. Response THD +N Crosstalk Bit Error Rate (BER) Signal to Noise (unweighted) Digital Outputs A-Net Pro16 and Pro16e Latency Power Supply
      Input Voltage
      Output Voltage
      Plug Size Power Dimensions Weight Options
16, balanced line-level, 1/4-inch TRS connector
Tip: Audio +; Ring: Audio -; Sleeve: Ground
Impedance matched output
48kHz sample rate, 24 bit
One Category 5 (RJ45 connector)
Four-position slot range selector switch for use with Pro16e A-Net
One Category 5 (RJ45 connector)
Supports Pro16 and Pro16e
Four-position switch, -10dBv, 0dBu, +4dBu, and +22dBu
Signal Present and Clip, per channel
Impedance: 48k ohms
LEDs; green: Signal Present, red: Clip; per channel
Stereo Link, per channel pair;
Two-position switch (Normal, Link)
17.8k ohm
4Hz-22kHz +0.2dB/-3dB
< 0.003%
90dB typical, A/D to D/A
Measured from AN-16/i to AN-16/o Output Module
A-Net: 1; RJ45 connector

Use unshielded Cat-5e UTP (or better) cable

<0.880 msec (measured from analog input to analog output)
External, DC, universal switching type
100-240 volts, 50/60Hz, 30VA
18-24 VDC, 0.5 amp
2 mm
18-24 VDC, 500mA
19" (482.6 mm) wide x 5.75" (146 mm) deep;
1U high
6.8 lb (3.08 kg)
AN-16SBR System Bridge; used to combine up to four A-Net streams for transmission over one Cat-5e cable



A-16II Personal Mixer

Audio Output Line/Headphone TRS Output A-Net Input/Output Digital to Analog Conversion Bit Depth Signal to Noise Ratio Latency Pro16 A-Net Tone Controls Maximum Levels (RMS) Impedance Power Supply
      Input Voltage
      Output Voltage
      Plug Size Dimensions Weight Options
1/4-inch TRS stereo, headphone or line level
Tip: Audio Left; Ring: Audio Right;Sleeve: Ground
Auto-detects mono plugs
1 A-Net input, 1 A-Net output; Category 5 (RJ45 connector)
24 bit
(Referenced to 0dB) -103dB
<0.880 msec (measured from analog input to analog output)
Uses unshielded Cat-5e UTP (or better) cable; maximum 500ft (150m) between devices
Treble +/-12dB at 9kHz shelving
Bass +/-12dB at 160Hz shelving
Line/Headphone outs: 1.0 watt at 100 ohms
Line/Headphone outs: 32 ohms
External, DC, universal switching type
100-240 volts, 50/60Hz, 30VA
18-24 VDC, 0.5 amp
2 mm
10.75" (273 mm) wide x 5.6" (142.2 mm) deep;
2.25" (57.5 mm) high 
3.4 lbs. (1.54 kg)
MT-1 or MT-1a Mic Stand Mount
EB-1 Extension Bracket
MT-X Expansion Box (requires MT-1)
PS-120 Power Supply



A-16D Pro A-Net Distributor

A-Net Input A-Net Thru A-Net Outputs LEDs Pro16 A-Net Power Supply Cooling Input Voltage Output Voltage for
Personal Mixers Dimensions Weight
One EtherCon RJ45 connector
One EtherCon RJ45 connector, unpowered
8 EtherCon RJ45 connectors, powered (DC)
Power On; A-Net Active
16 channels of digital audio over Cat-5e cable
Uses unshielded Cat-5e UTP (or better) cable
Internal, universal switching type
One ultra-quiet fan
100-240VAC, 50-60Hz, 60W
18-24 VDC, 0.5 amp
Transmitted over the Cat-5e cable
19" (482.6 mm) wide x 14.25" (362 mm) deep; 2U,
3.5" (88.9 mm) high
12.0 lbs (5.44 kg)



MT-1a Mic Stand Mount

Boxed Weight Boxed Dimensions Dimensions Connections: Connectors:
1 lb
7"w x 5"d x 3"h
6.25" wide at front x 4.5" wide at rear x 3" high
Attaches with three screws to bottom of an A360 A-16II, or A-16CS
Size: 6-32, 1/4-inch long screws

Call 1-877-477-6432 for any technical questions or if you need SPECIAL PRICING regarding this product