Aviom AN-16/o v.4 16-Channel Mic- and Line-Level Output Module

Vendor: Aviom
Description Aviom AN-16/o v.4 16-Channel Mic- and Line-Level Output Module Aviom AN-16/o v.4 is an output module designed for connecting to any Pro16 input module, A-Net distributor, or console card and provides 16 balanced line-level analog outputs...
$1,499.00 $1,599.00
Title

Aviom AN-16/o v.4 16-Channel Mic- and Line-Level Output Module

Aviom AN-16/o v.4 is an output module designed for connecting to any Pro16 input module, A-Net distributor, or console card and provides 16 balanced line-level analog outputs by the use of two DB25 multi-pin connectors. From mic to +24dBu, four output levels, are available for easy accommodating the input level requirements of the device the AN-16/o v.4 output signals are being connected to.

This Aviom AN-16/o v.4 can be use anywhere where analog outputs are required: with the A360 and D800's Network Mix Back created for wireless in-ears, in the studio, on stage or at FOH in a digital snake, or for a recording split. Things made simple, adding a digital split to a Pro16 system is just like as connecting an additional AN-16/o v.4 Output Module.

Product Details

The Aviom AN-16/o v.4 Output Module is designed as a 1U rack-mount 16-channel digital-to-analog converter for audio distribution and digital snake systems. By the use of Aviom's A-Net® Pro16 digital audio transmission protocol, the digital audio transmitted to the AN-16/o v.4, is converted to analog using 24-bit, 48kHz converters.

By the use of DB25 multi-pin connectors, the sixteen balanced outputs are provided on the rear panel. The DB25 connectors are connected by wires to the analog standard, making it allow you to purchase whatever connector and cable length format suits your application. The analog outputs can be set (per channel pair) to +24dBu, +18dBu, +4dBu, or mic level.

Connecting to Wireless In-Ear Monitors

In personal mixing systems using the A360 Personal Mixer with the D800 or D800-Dante A-Net Distributors, the AN-16/o v.4 simplifies connections to wireless IEM systems.

Each A360 Personal Mixer sends its stereo mix output back into the network which appears as a pair of channels on the AN-16/o v.4. Each AN-16/o v.4 supports up to eight A360s. Simply patch the analog outputs on the AN-16/o v.4 into the IEM transmitter's inputs. No analog cables are required at the A360 on stage. Learn more about Network Mix Back.

Digital Snakes and Audio Networks

Use the AN-16/o v.4 anywhere analog outputs are required: on stage or FOH in a digital snake, in the studio, for a recording split, or in even the most complex audio networks. Adding a digital split to a Pro16 system is as simple as connecting an additional AN-16/o v.4 Output Module.

Audio Outputs 16 channels, balanced
Outputs DB25 multipin connectors (2); Tascam® analog audio pinout
Impedance balanced output for mic, +4dBu, and +18dBu; differential output for +24dBu

Breakout cables are not included
D/A Conversion 48kHz sample rate, 24 bit
Frequency Response 4Hz-22kHz
A-Net Input/Output one EtherCon Category 5 (RJ45 connector)
A-Net Expansion one EtherCon Category 5 (RJ45 connector)
Output Level Settings Four-position switch, per channel pair;
+24dBu, +18dBu, +4dBu, and Mic
Channel LED Indicators Signal Present and Clip, per channel
Metering LEDs; green: Signal Present; red: Clip; per channel
Maximum Output Level +24dBu
Output Impedance 226 ohms (+18dBu, +24dBu); 100 ohms (+4dBu and mic)
Freq. Response 4Hz-22kHz +0.2dB/-3dB
THD +N < 0.004%
Crosstalk -90dB
Bit Error Rate (BER) 10(-12)
Signal to Noise (unweighted) 92dB typical, A/D to D/A
Measured from AN-16/i to AN-16/o v.4 Output Module
Digital Connections A-Net In: 1; A-Net Out: 1; A-Net Expansion: 1;
Neutrik EtherCon connectors
A-Net Pro16 A-Net Expansion combines two A-Net streams (32 channels of audio) onto one Cat-5e cable;
uses unshielded Cat-5e UTP (or better) cable
Latency <0.620 msec (measured from analog input to analog output)
Power Supply
      Input Voltage
      Output Voltage
      Plug Size
External, DC, universal switching type
100-240 volts, 50/60Hz, 30VA
24 VDC, 0.5 amp
2 mm
Power 24 VDC, 500mA
Dimensions 19" (482.6 mm) wide x 5.75" (146 mm) deep;
1U high
Weight 6.8 lbs. (3.08 kg)
Options SB4 System Bridge; used to combine up to four A-Net streams for transmission over one Cat-5e cable

DB25 breakout cables