Community C6 6.5-Inch Ceiling Loudspeaker

Vendor: Community
Community C6 6.5-Inch Ceiling Loudspeaker The Community C6 comes with a more focused dispersion and a greater low frequency extension than the smaller C4. It is professionally designed containing a proprietary Tru-Phase™ waveguide that comes producing a...
$184.00
Title

Community C6 6.5-Inch Ceiling Loudspeaker

The Community C6 comes with a more focused dispersion and a greater low frequency extension than the smaller C4. It is professionally designed containing a proprietary Tru-Phase™ waveguide that comes producing a consistently wide conical polar response up to 16 kHz. The C6 comes featuring a genuine coaxial design with the use of separate magnets for the LF and HF drivers for having reduced distortion and high sensitivity, thereby it permits up to 3 dB greater output level while also requires up to half the amplification power of competing products at the same time. The C SERIES ceiling loudspeakers are all ETL listed, and have similar sensitivity and output capabilities.

Features

  • High intelligibility with exceptional uniform coverage
  • Consistent, wide dispersion up to 16 kHz
  • True coaxial loudspeakers with HF compression drivers
  • Tru-Phase™ high-frequency waveguide
  • Spring loaded Drop-Stop™ installation assistant tabs support the back can on the included rails simplify installation
  • Uniquely designed tile bridge support rails prevent ceiling tile sagging
  • External loop-through Euroblock connectors
  • Rear cover with integrated cable clamp (strain relief) and optional conduit knockout
  • Face-mounted adjustable tap position selector switch
  • Selectable 8 ohm or 70V/100V operation
  • Loudspeaker Type: Two-way, full-range, coaxial ceiling loudspeaker, 8 ohm or 70V/100V operation
  • Operating Range: 70 Hz - 13.5 kHz (-10 dB)
  • Frequency Response: 115 Hz - 12.5 kHz (-3 dB)
  • Max Input Ratings (8 ohm):
    • 60W continuous, 150W program
    • 21.9 volts RMS, 43.8 volts momentary peak
  • Transformer Taps:
    • 70V: 30W, 15W, 7.5W, 3.75W, and 8 ohm selectable
    • 100V: 30W, 15W, 7.5W, and 8 ohm selectable
  • Sensitivity (1W/1m):
    • 91 dB SPL (125 Hz to 12.5 kHz 1/3 octave bands)
    • 91 dB SPL (250 Hz to 4 kHz speech range)
  • Maximum Output
    • 8 Ohm: 109 dB SPL / 115 dB SPL (peak)
    • 70V: 106 dB SPL / 112 dB SPL (peak)
    • 100V: 106 dB SPL / 112 dB SPL (peak)
  • Nominal Impedance: 8 ohms
  • Minimum Impedance: 7 ohms @ 10 kHz
  • Nominal Coverage:
    • 120º conical (1 kHz to 6 kHz ±65°)
    • 120° conical (500 Hz to 6 kHz ±65°)
  • Axial Q / DI: 4.9/6.9, 500 Hz to 6 kHz
  • Crossover Frequency: 2 kHz
  • Recommended Signal Processing: 100 Hz, at 24 dB per octave high pass filter
  • Drivers:
    • LF 1 x 6.5" cone
    • HF 1 x 3/4" exit compression driver
  • Driver Protection: Self-resetting solid state circuitbreaker
  • Input Connection: 4-pole Euroblock connector with two pair of non-interrupt parallel connections
  • Controls: Front-face wattage / low impedance selector switch
  • Enclosure: Corrosion-resistant zinc plated steel
  • Finish: White or black
  • Mounting/Rigging Provisions: 2 ABS mounting clamps with 1.75-inch grip range
  • Grille: Powder coated steel with safety line, white or black finish, paintable
  • Safety Features: 2 x safety hang points
  • Safety Agency Ratings: ETL listed to comply with UL1480, UL2043 and CSA60065. Suitable for use in air handling spaces per NFPA70 and NFPA 90.
  • Required Accessories: Electronic high pass filter
  • Supplied Accessories: Tile support bridge rails,grille, paint mask, cut-out template, flat screwdriver
  • Optional Accessories:
    • C6-CATR Can Adapter / Trim Ring (white)
    • C6-CATR-B Can Adapter / Trim Ring (black)
    • C6-NCB New Construction Bracket
  • Depth:
    • 9.80" (248.9 mm) bezel diameter
    • 6.49" (164.8 mm) can depth
  • Weight: 7.1 lbs (3.2 kg)
  • Baffle: Reflex loaded UL 94V-0 rated ABS
  • Cutout Diameter: 8.86" (225 mm)