QSC ISA450 2 channels, 260 watts/ch at 8Ω, 425 watts/ch at 4Ω, 700 watts/ch at 2Ω

Vendor: QSC
Description QSC ISA450 2 channels, 260 watts/ch at 8Ω, 425 watts/ch at 4Ω, 700 watts/ch at 2Ω The QSC ISA450 is, one of the ISA Installed System Amplifiers, professionally designed to meet the needs of...
$800.00
Title

QSC ISA450 2 channels, 260 watts/ch at 8Ω, 425 watts/ch at 4Ω, 700 watts/ch at 2Ω

The QSC ISA450 is, one of the ISA Installed System Amplifiers, professionally designed to meet the needs of the system contractors and designer all around the world. In this ISA system there are three models that features isolated 25, 70, and 100 volt outputs for distributed sound systems, while four low impedance models are rated for 2 ohm operation. The ISA Series is a rugged and cost-effective power solution, because of its comprehensive set of features and versatile loading options, for any permanently installed sound system. It is the QSC ISA450 2 channels, 260 watts/ch at 8Ω, 425 watts/ch at 4Ω, 700 watts/ch at 2Ω.

Features

  • Rear panel gain controls for tamper resistance; 2-dB detents allow for quick and repeatable settings
  • XLR and detachable Euro-style input connectors
  • DataPort V2 for use with DPV2-compatible signal processing accessories (XC-3, SF-3, LF-3) and DSP-3/DSP-4 (with external power supply)
  • Independent defeatable clip limiters for reduced distortion
  • Selectable high-pass filters (30 Hz or 70 Hz) protect speakers and prevent speaker transformer saturation with minimal effect on program material
  • Front panel LED indicators include power, signal, and clip
  • Covered barrier strip output connectors for safety agency compliance
  • Automatic on-demand variable-speed fan: quiet normal operation, with maximum cooling when needed
  • Rear-to-front air flow helps keep equipment racks cool
  • Stereo, bridge, or parallel operating modes
  • Comprehensive protection circuitry including DC, infrasonic, thermal overload, and short circuit protection
  • 3-year warranty plus optional 3-year extended service contract
SPECIFICATIONS ISA450
  OUTPUT POWER PER CHANNEL, STEREO MODE, both channels driven
8Ω, 20 Hz–20 kHz 0.1% THD
4Ω, 20 Hz–20 kHz 0.1% THD
2Ω 1 kHz 1% THD
260 W
425 W
700 W
  DIRECT POWER PER CHANNEL, STEREO MODE
70V, 20 Hz–20 kHz +0/-0 .3 dB 0.5% THD -
  TRANSFORMER-ISOLATED OUTPUT POWER PER CHANNEL, STEREO MODE
70V or 100V, 50 Hz–16 kHz 0.5% THD
25V, 50 Hz–16 kHz 0.5% THD
-
-
  OUTPUT POWER, BRIDGED MONO MODE
8Ω, 1 kHz 0.1% THD
4Ω 1 kHz 1% THD
900 W
1400 W
  TRANSFORMER-ISOLATED OUTPUT POWER, BRIDGED MONO MODE
140V or 200V, 50 Hz-16 kHz 0.5% THD -
Signal to Noise (20 Hz-20 kHz) 100 dB
Distortion (SMPTE-IM) Less than 0.01%
Input Sensitivity @ 8 ohms 1.07 V
(+2.8 dBu)
Maximum Voltage Gain 44.7×
(33 dB)
Output Circuitry Class AB
THX Approved Yes
Weight - Net 42 lb
(19 kg)
Weight - Shipping 48 lb
(22 kg)
  ALL MODELS
Distortion (Typical)
20 Hz–20 kHz: 10 dB below rated power
1.0 kHz and below: full rated power
Less than 0.03% THD, 4 ohms and 8 ohms

Less than 0.03% THD, 4 ohms and 8 ohms
Frequency Response
10 dB below rated output power
ISA 280, 450, 750 and 1350: 
20 Hz–20 kHz, +0/-1 dB; -3 dB points: 5 Hz and 50 kHz
ISA 300Ti, 500Ti and 800Ti: 
Direct outputs: -3 dB @ 50 Hz, -0.5 dB @ 20 kHz; XF outputs: 50 Hz–16 kHz, +1/-3 dB
Damping Factor with 8Ω Load (direct outputs) Greater than 200; ISA 1350 greater than 250
Output Regulation (isolated outputs) Less than 1.5 dB
Input Impedance 10 kΩ unbalanced, 20 kΩ balanced
Input Clipping 10 V rms (+22 dBu)
Cooling Continuously variable speed fan, back-to-front air flow
Connectors, each channel Input: Active balanced; 3-pin Euro-style detachable terminal block and XLR (pin 2+)
Output: Covered barrier strips 
DataPort V2: HD-15 connector
Controls Front: AC switch
Rear: Ch. 1 and Ch. 2 gain knobs, 10-position DIP switch
Indicators PWR-ON: Green LED; SIGNAL: Green LED (1 per channel);
CLIP: Red LED (1 per channel)
Dimensions (HWD) inches 5.25 x 19 x 15.9 / 3RU
Dimensions (HWD) mm 133 x 483 x 400 / 3RU
Amplifier Protection Full short circuit, open circuit, thermal, ultrasonic, and RF protection;
Stable into reactive or mismatched loads
Power Requirements 120 or 230 VAC, 50–60 Hz
Load Protection On/off muting; Triac crowbar: ISA 750, 1350, and 800Ti; AC coupling: ISA 280, 300Ti, 450, and 500Ti