Martin Audio SXP218, High-performance 2x 18" Powered Subwoofer System Black & White

Vendor: Martin Audio
Martin Audio SXP218, High-performance 2x 18" Powered Subwoofer System Black & White Martin Audio SXP218 a self-powered system it also incorporates a Class D amplifier, DSP, and Dante™ digital audio networking it simplifies set-up, enhancing...
$5,460.00
Color
BLACK
WHITE

Martin Audio SXP218, High-performance 2x 18" Powered Subwoofer System Black & White

Martin Audio SXP218 a self-powered system it also incorporates a Class D amplifier, DSP, and Dante™ digital audio networking it simplifies set-up, enhancing control, and eliminating amplifier racks. The onboard amplifier delivers a total of 4000W peak output to the drivers and its switched-mode power supply auto-ranges to global mains voltages from 100 to 240V 50/60Hz. DSP functions — including parametric EQ, delay, muting, gain, and preset selection — can be controlled over Ethernet from a PC or Windows® tablet via intuitive VU-NET™ proprietary software. For simple set-ups, ‘plug-and-play’ presets for operation with the CDD-LIVE 8, CDD-LIVE 12, or CDD-LIVE 15 — as well as a user-defined preset — can be selected on the rear panel, instead of using computer control. Additional presets provide the appropriate settings for the rear-facing subwoofer in a cardioid pair. As an alternative to its analog inputs, the Martin SXP218 is Dante enabled for digital audio distribution and control over a single CAT5 cable to maintain audio quality however long the cable run. Martin Audio SXP218 enclosure is constructed from multi-laminate plywood with a durable polyurea coating and equipped with a perforated Zintec grille, four grab handles, skids, and M10 flying inserts. SXP218 also features an M20 pole mount insert for added versatility in deployment. The product is supplied as standard without cabinet wheels, but they are available as an accessory. By adding the input board cover accessory, the subwoofer is fully weather resistant and suitable for permanent outdoor usage.

Martin Audio SXP218 Main Key Features 

  • Dual-driver, self-powered subwoofer
  • 2 x 18” (460mm) drivers with 4” (100mm) voice coils
  • Very high output capability
  • Onboard Class D amplification and DSP
  • Dante™ Digital Audio networking
  • Global mains operation with Power Factor Correction
  • Tour-grade plywood enclosure with flying inserts
  • IP24 rating option with rain cowl
TYPE  Dual-driver, direct-radiating powered subwoofer
FREQUENCY
RESPONSE (3)
 35Hz – 150Hz ±3dB, -10dB @ 30Hz
DRIVER  2x 18” (460mm)/4” (100mm) voice coil, long   excursion, ferrite magnet,
 waterproof cone
INPUT SENSITIVITY  -30dBu for 100dB SPL
MAXIMUM SPL (4)  140dB continuous / 143dB peak
DISPERSION  Omnidirectional / or Cardioid (paired)
CROSSOVER  Active Presets for CDD Live 8, 12 & 15 mono-pole or  cardioid (paired)
MODULE
AUDIO INPUT
CONNECTORS  Female XLR input, male XLR link output, Dante Audio Neutrik® Ethercon
ANALOGUE INPUT IMPEDANCE  20 kΩ balanced to ground
MAXIMUM ANALOGUE INPUT LEVEL  24.6 Vpp (+21dBu), over-voltage protected
INTERNAL PROCESSING  Multi-channel DSP, programmable via TCP/IP using   VU-Net software
 PEQ/shelving filters
 Up to 48dB/Oct LPF
 Up to 200mS input delay
 Pre-set selection via a rear panel switch
NETWORK
CONNECTORS  2 x Neutrik® Ethercon RJ45
PROTOCOL  TCP/IP and UDP/IP
AMPLIFIER MODULE
TYPE  Two 2 channel switch-mode, class D,
 Bridged Tied Load
PEAK OUTPUT POWER  4000W
AVERAGE EFFICIENCY  89%
COOLING  External fan
MAXIMUM AMBIENT TEMPERATURE  40°C (104°F) for full output
POWER SUPPLY
TYPE  Switch mode, the fixed frequency with PFC
AC INPUT OPERATING RANGE  85 – 265V ~ AC, 50 - 60Hz
POWER FACTOR  > 0.98
NOMINAL POWER CONSUMPTION  250W
MAINS CONNECTOR  Neutrik® Powercon True1
MECHANICAL
ENCLOSURE  Extensively braced multi-laminate birch plywood.
FINISH  Durable Polyurea Coating
PROTECTIVE GRILLE  Black perforated Zintec
FITTINGS
  • Two skids on base, with mating channels on top
  • 16 x M8 inserts for optional castors
  • 24 x M10 mounting points
  • 4x Bar handles, 2 on each side
  • 4x fittings for optional transit cover
  • M20 Pole mount insert
IP RATING  IP24 factory option available
DIMENSIONS  (W) 1085mm x (H) 537mm x (D) 792mm (920mm including castors)
 (W) 42.72in x (H) 21.13in x (D) 31.16in (36.20in including castors)
WEIGHT  101.5kg (224lbs) w/o castors 105kg (231lbs) with castors