Crown CDi DriveCore 2|600 Analog input, 2 channel, 600W per output channel, Amplifier

Vendor: Crown
Description Crown CDi DriveCore 2|600 Analog input, 2 channel, 600W per output channel, Amplifier The Crown CDi DriveCore 2|600 is one of the evolution in amplification designed professionally for providing an impressive and...
$1,889.18
Title

Crown CDi DriveCore 2|600 Analog input, 2 channel, 600W per output channel, Amplifier

The Crown CDi DriveCore 2|600 is one of the evolution in amplification designed professionally for providing an impressive and wonderful mix of high-performance; rich feature set, and competitive cost. With the use of technology that is adopted from the Crown's flagship Installed Sound amplifier (Crown DriveCore Install series), the Crown CDi DriveCore 2|600 has arrived capable of offering streamlined functionality to work in almost any medium sized installation such as bars, cinema, lounges, houses of worship, and more. The Crown CDi DriveCore 2|600 is professionally designed for ease-of-use in a variety of applications, also it is a 2-channel amp including the high-level DSP, network control/monitoring, front-panel interface, and support for driving up to 100Vrms speaker loads even with the absence and not requiring a transformer. The 2|600 also comes with BLU link, that makes it capable to send and receive channels over HARMAN’s digital audio BUS. The entire CDi DriveCore line can get with pre-loaded with JBL speaker tunings for a much quicker and easier installations. 

Features

CDi DriveCore Model Channels Network Control DSP Control Port BLU link
2|600 2  


Output Power: Dual Mode - All Channels Driven

CDi DriveCore Model Channels 16Ω 70Vrms 100Vrms
2|600 / 2|600BL 2 300W 600W 600W 300W 600W 600W


Minimum Guaranteed Power (1kHz, all channels driven, max distortion 0.5%, duration 0.5 seconds, 120 - 240Vrms - 50/60Hz)

Output Power: Bridge Mono Mode - All Channels Driven

CDi DriveCore Model  16Ω 140Vrms 200Vrms
2|600 / 2|600BL 600W 1200W 1200W 1200W 1200W


Minimum Guaranteed Power (1kHz, all channels driven, max distortion 0.5%, duration 0.5 seconds, 120 - 240Vrms - 50/60Hz)

Features

DriveCore Technology – Crown’s proprietary DriveCore technology eliminates hundreds of components within each amplifier, reducing the variability of component values, increasing reliability, resulting in incredible audio fidelity from an efficient design.

Network Control and Monitoring – Through Harman’s HiQnet Audio Architect software, the CDi DriveCore can be controlled, configured, and monitored through standard TCP/IQ network.

DSP – On-board Digital Signal Processor in each amplifier allows for custom configuration

  • Input Router
  • Input Delay – Up to 1000ms
  • Input Parametric EQ – 8 band
  • Crossover
  • Output Parametric EQ – 8 band
  • Output Delay – Up to 100ms
  • LevelMAX™ Limiter

BLU link (BL models only) – Both receive and send channels over HARMAN’s 256 channel, fault-tolerant audio BUS, BLU link

Direct Drive 70/100Vrms Output – Each output channel is capable of provide either 70V or 100V for high impedance applications.

Front-Panel Interface – Completely configure the amplifier using an intuitive front-panel interface.

GPIO/AUX Port – Recall presets, mute channels, monitor faults, power on/off the amplifier, and more through a combined GPIO/AUX Port.

BLU link No
Channels 2
Sensitivity (for full rated power at 8 ohms) 0.7V RMS
Rated Power Output (per channel @ 4 ohms) 600W
Analog Input Signal to Noise Ratio (ref. rated power, 100V, 20Hz - 20kHz) at 8 ohms) > 104dB
THD (full rated power, 20 Hz - 20 kHz) 0.35%
Damping Factor (20 Hz to 100 Hz) > 1000
Frequency Response (8Ω, 20 Hz - 20 kHz) +/-0.5dB
Crosstalk (below rated power) 20 Hz to 1 kHz > 80dB
Input Impedance (nominally balanced, nominally unbalanced) 20 kΩ balanced, 10 kΩ unblanced
Dimensions (inches) (W x H x D) (depth not including 1.3 inch front panel protrusion) 19 x 3.5 x 12.25
Weight 14.56 lbs (6.6 kg)
Power Supply Connector "Standard IEC type 320 inlet for detachable connector 100 – 240V~"