Descriptions Williams Sound WF T5 D, WaveCAST assistive listening system (DANTE) The Williams Sound WF T5 D is a Wi-Fi platform designed for pro-audio applications where high-quality sound is required. This Williams Sound WF...
Williams Sound WF T5 D, WaveCAST assistive listening system (DANTE)
The Williams Sound WF T5 D is a Wi-Fi platform designed for pro-audio applications where high-quality sound is required. This Williams Sound WF T5 D is built on a hardware-based DSP audio system architecture, allowing system optimization to achieve the best quality experience for the particular audio stream being delivered. Hearing assistance can be optimized for hearing loss, music can be optimized for high-fidelity playback, and voice can be set for maximum speech intelligibility. Custom pre-sets can also be established for specific performance applications.
Professional audio inputs on the Williams Sound WF T5 D include 1/4” XLR connectors, phantom power and a line level output jack. In addition to multi-stage gain control inputs, the DSP features include AGC, limiters, high and low pass filter, and adjustable range compressor control. Also, the Williams Sound WF T5 D has a 16-bit DAC provides a 48Khz sample rate for a smooth digital stream and minimizes digital harshness. The Williams Sound WF T5 D also supports both unicast and multicast network configurations. Up to four WaveCAST systems can be connected to the same Wi-Fi network to provide multiple listening channels — supporting 45 users in unicast mode or 1500+ users in multicast mode.
The Williams Sound WF T5 D Dante interface is based on the Audinate UXT Ultimo chipset. This chipset supports both AES67 and SMPTE 2110. Dante’s Ultimo UXT support of AES67 and SMPTE 2110 allows integrators multiple audio options to chose from for greater interoperability with other audio equipment with their system design. This allows the WF T5 D to be controlled by the Dante Controller — the very easy-to-use software from Audinate for setting up and managing audio routing of Dante-enabled products on an audio network. The Williams Sound WF T5 D can have most settings changed via the front panel interface, or the hosted web interface. A remote programming guide is available upon request. The new Williams Sound WF T5 D app provides an easy-to-use, intuitive user interface and is available in iOS or Android. Listeners easily select channel and volume level once their personal device is connected to the Wi-Fi network.
Williams Sound WF T5 D Main Features
Dante’s Ultimo UXT support of AES67 and SMPTE 2110 allows integrators multiple audio options
8.45″ W x 8.25″ D x 1.72″H (21.5 cm x 21 cm x 4.4 cm)
Weight:
Transmitter: 3.0 lbs (1.36 kg)
Color
Black/Silver with silver legends on the front, white legends on the back
Rack Mount
Standard 19″ Rack, one EIA rack space high, 1/2 space wide 1–2 units can be mounted in a single rack space with optional RPK 005 (single) or RPK 006 (double) Rack Mount Kits
Power Supply
Desktop Style Transformer (TFP 062); Input: 100-240 VAC, 50/60 Hz. IEC Line Cord; Output: 24 VDC, 750 mA, 18W. 2.5mm ID center positive barrel connector
Power ON Indicator
Push On/Push Off latching power button, backlit green indicates power ON, backlight off indicates power OFF, fading from bright to dark indicates Sleep Mode.
Temperature Range
Operating: +32° F to +104° F (0° C to 40° C); Storage: -4° F to +158° F (-20° C to 70° C)
Audio Processor Functions
DSP based; Compression: 1:1, 1.5:1 or 2:1; High-pass and Low-pass Filter Frequency control
Frequency Response
31 – 16000 Hz, ±3 dB (Music Audio Preset)
Signal-to-Noise Ratio
Greater than or equal to 74 dB Transmitted RF
Total Harmonic Distortion
Less than 0.25% @ 1 kHz (RF output)
Common Mode Rejection
Greater than 57 dB @ 1 kHz, Mic or Line
User Interface
Front panel buttons or hosted web interface
Audio Inputs
(1x) Combination 3-pin XLR, 1/4″ (TRS) jack for Mic or Line Level Analog Audio, Balanced or Unbalanced Line Level, or balanced or unbalanced microphone with Selectable Phantom Power
Audio Input Gain Adjust
In menu, adjustable to 0 to -50 dB, in 1dB steps
Phantom Power
14.4 VDC applied through 2.2 kΩ resistors to analog combo jack: Pin 2 and Pin 3 on XLR jack, or tip and ring on 1/4” TRS jack
Audio Level Indicators
10-LED array that reads -18 to +9 dB at 3 dB intervals. 7 Green, 2 Amber, and 1 red LED. Green LEDs indicate normal operating audio level peaks, Amber LEDS indicate close to overload peaks, Red LED indicates overload peaks
Headphone Output
1/4″ TRS stereo jack, mono signal, 15.7 mW, maximum in 33 Ω (level adjustable in menu 0 to -40 dB in 2 dB steps)
Descriptions Williams Sound WIR RX22-4N, Body-pack, 4-channel, infrared receiver. 2.3/2.8/3.3/3.8 MHz. No batteries. No earphones. The Williams Sound WIR RX22-4N...
Descriptions Williams Sound IR RX20, Under-the-chin-style infrared receiver 2.3/stereo/2.8 MHz. Rechargeable. The Williams Sound IR RX20 is a comfortable, stereostethoscope...
Descriptions Williams Sound POE 001, Optional power-over-Ethernet transformer for IR T2 infrared transmitter The Williams Sound POE 001 is an optional,...
Descriptions Williams Sound IR T2, Commercial-grade, medium-area infrared transmitter ideal for assistive listening and language interpretation in commercial spaces. The...
Descriptions Williams Sound IR T1-00, Small-area infrared transmitter. The new! Williams Sound IR T1-00 is a small-area infrared emitter. This Williams...
Descriptions Williams Sound IR SY6, Commercial-grade, medium-area infrared transmitter system. Portable Infrared ADA Compliance Kit for Courts The Williams Sound...
Descriptions Williams Sound IR SY5, Commercial-grade, medium-area infrared transmitter system. Building on years of infrared audio delivery expertise, Williams Sound...
Descriptions Williams Sound IR SY4, Commercial-grade, medium-area infrared transmitter system. Building on years of infrared audio delivery expertise, Williams Sound...
FREE CHURCH DESIGNS
Call us 1-877-477-6543 or email us at sales@muzeekworld.com
USD
EUR
AUD
GBP
JPY
