Community C6 6.5-Inch Ceiling Loudspeaker

Community C6 6.5-Inch Ceiling Loudspeaker

The Community C6 comes with a more focused dispersion and a greater low frequency extension than the smaller C4. It is professionally designed containing a proprietary Tru-Phase™ waveguide that comes producing a consistently wide conical polar response up to 16 kHz. The C6 comes featuring a genuine coaxial design with the use of separate magnets for the LF and HF drivers for having reduced distortion and high sensitivity, thereby it permits up to 3 dB greater output level while also requires up to half the amplification power of competing products at the same time. The C SERIES ceiling loudspeakers are all ETL listed, and have similar sensitivity and output capabilities.

Features

• High intelligibility with exceptional uniform coverage
• Consistent, wide dispersion up to 16 kHz
• True coaxial loudspeakers with HF compression drivers
• Tru-Phase™ high-frequency waveguide
• Spring loaded Drop-Stop™ installation assistant tabs support the back can on the included rails simplify installation
• Uniquely designed tile bridge support rails prevent ceiling tile sagging
• External loop-through Euroblock connectors
• Rear cover with integrated cable clamp (strain relief) and optional conduit knockout
• Face-mounted adjustable tap position selector switch
• Selectable 8 ohm or 70V/100V operation

• Loudspeaker Type: Two-way, full-range, coaxial ceiling loudspeaker, 8 ohm or 70V/100V operation
• Operating Range: 70 Hz - 13.5 kHz (-10 dB)
• Frequency Response: 115 Hz - 12.5 kHz (-3 dB)
• Max Input Ratings (8 ohm):
• 60W continuous, 150W program
• 21.9 volts RMS, 43.8 volts momentary peak
• Transformer Taps:
• 70V: 30W, 15W, 7.5W, 3.75W, and 8 ohm selectable
• 100V: 30W, 15W, 7.5W, and 8 ohm selectable
• Sensitivity (1W/1m):
• 91 dB SPL (125 Hz to 12.5 kHz 1/3 octave bands)
• 91 dB SPL (250 Hz to 4 kHz speech range)
• Maximum Output
• 8 Ohm: 109 dB SPL / 115 dB SPL (peak)
• 70V: 106 dB SPL / 112 dB SPL (peak)
• 100V: 106 dB SPL / 112 dB SPL (peak)
• Nominal Impedance: 8 ohms
• Minimum Impedance: 7 ohms @ 10 kHz
• Nominal Coverage:
• 120º conical (1 kHz to 6 kHz ±65°)
• 120° conical (500 Hz to 6 kHz ±65°)
• Axial Q / DI: 4.9/6.9, 500 Hz to 6 kHz
• Crossover Frequency: 2 kHz
• Recommended Signal Processing: 100 Hz, at 24 dB per octave high pass filter
• Drivers:
• LF 1 x 6.5" cone
• HF 1 x 3/4" exit compression driver
• Driver Protection: Self-resetting solid state circuitbreaker
• Input Connection: 4-pole Euroblock connector with two pair of non-interrupt parallel connections
• Controls: Front-face wattage / low impedance selector switch
• Enclosure: Corrosion-resistant zinc plated steel
• Finish: White or black
• Mounting/Rigging Provisions: 2 ABS mounting clamps with 1.75-inch grip range
• Grille: Powder coated steel with safety line, white or black finish, paintable
• Safety Features: 2 x safety hang points
• Safety Agency Ratings: ETL listed to comply with UL1480, UL2043 and CSA60065. Suitable for use in air handling spaces per NFPA70 and NFPA 90.
• Required Accessories: Electronic high pass filter
• Supplied Accessories: Tile support bridge rails,grille, paint mask, cut-out template, flat screwdriver
• Optional Accessories:
• C6-CATR Can Adapter / Trim Ring (white)
• C6-CATR-B Can Adapter / Trim Ring (black)
• C6-NCB New Construction Bracket
• Depth:
• 9.80" (248.9 mm) bezel diameter
• 6.49" (164.8 mm) can depth
• Weight: 7.1 lbs (3.2 kg)
• Baffle: Reflex loaded UL 94V-0 rated ABS
• Cutout Diameter: 8.86" (225 mm)