Community D10 10-Inch Ceiling Speaker

Community D10 10-Inch Ceiling Speaker

The Community D10 comes with a more focused dispersion, higher sensitivity, output and greater LF extension than the smaller models. The high performance D10 is a professionally designed true coaxial loudspeaker that comes along with a real compression driver concentrically arranged so that the upper frequencies emerge through the center of the low-frequency driver’s magnetic structure and cone with the use of a precisely tapered Tru-Phase™ high-frequency waveguide. This special construction is capable of providing a consistent, wide dispersion up to 16 kHz, all but eliminating high-frequency narrowing. Further pattern improvement is also achieved by precisely mounting the low frequency driver (and its concentric HF driver) centered in the baffle, as contrasted to the offset designs used by others.

The D SERIES comes offering powerful magnetic structures and efficient coils for ensuring high output, which comes resulting in more headroom per power amplifier. Each D SERIES ceiling model comes including the everything needed for standard installations, and comes with a built-in autoformer allowing it to be used in 8-ohm or 70V/100V applications. The D SERIES ceiling loudspeakers are ETL listed and all models have been tested by ETL for complying along with UL1480, UL2043 and CSA60065.

Features

• High intelligibility with exceptional uniform coverage
• Consistent, wide dispersion up to 16 kHz
• True coaxial loudspeakers with HF compression drivers
• Tru-Phase™ high-frequency waveguide
• Patented Carbon Ring Cone Technology™
• Spring loaded Drop-Stop™ installation assistant tabs support the back can on the included rails and C-ring to simplify installation
• Uniquely designed tile bridge support rails and snap-on C-ring support plates prevent sag
• Twist-Assist™ loudspeaker face retainer tabs for fast and easy installation
• 3/4" and 1" knock-outs on the sides of the back can
• External loop-through Euroblock connectors
• Rear cover with integrated cable clamp (strain relief) and optional conduit knockout
• Selectable 8 Ohm or 70V/100V operation
• Back can and face-only packages available
• Five year warranty

• Loudspeaker Type: Two-way, full-range, coaxial ceiling loudspeaker, 8 Ohm or 70V/100V operation
• Operating Range: 58 Hz - 22 kHz
• Frequency Response: 75 Hz - 20 kHz (+/- 5 dB)
• Max Input Ratings (8 Ohm): 200W continuous, 500W program, 40 volts RMS, 89 volts momentary peak
• Transformer Taps:
• 70V: 200W, 100W, 50W, 25W and low impedance
• 100V: 200W, 100W, 50W
• Distortion:
• 500 Hz, 10% Full Power: 0.92% 2nd Harmonic, 0.88% 3rd Harmonic
• 500 Hz, 1% Full Power: 0.17% 2nd Harmonic, 0.71% 3rd Harmonic
• 2 kHz, 10% Full Power: 0.81% 2nd Harmonic, 0.30% 3rd Harmonic
• 2 kHz, 1% Full Power: 0.07% 2nd Harmonic, 0.16% 3rd Harmonic
• 8 kHz, 10% Full Power: 2.9% 2nd Harmonic, 0.04% 3rd Harmonic
• 8 kHz, 1% Full Power: 1.04% 2nd Harmonic, 0.01% 3rdHarmonic
• Sensitivity (1W/1m): 98 dB SPL (100 Hz to 12.5 kHz 1/3 octave bands); 97 dB SPL (250 Hz to 4 kHz speech range)
• Maximum Output: 121 dB SPL / 127 dB SPL (peak 8 Ohm)
• Nominal Impedance: 8 Ohms
• Minimum Impedance: 6.6 Ohms @ 190 Hz
• Nominal Coverage: 88º conical (1 kHz to 6 kHz); 100º conical (500 Hz to 6 kHz)
• Axial Q / DI: 6.5 / 8.1, 500 Hz to 6 kHz
• Crossover Frequency: 1 kHz
• Recommended Signal Processing: 58 Hz high pass filter
• Drivers: LF 1x 10", HF 1x 1.25" exit compression driver
• Driver Protection: Self-resetting solid state circuit breaker
• Input Connection: 4-position Euroblock connector
• Controls: Front-face wattage / low impedance selector switch
• Enclosure: Corrosion-resistant zinc plated steel
• Mounting/Rigging Provisions: 4 steel mounting clamps with 3-inch grip range
• Grille: Powder coated steel with safety line, white finish, paintable
• Baffle: Reflex loaded UL 94V-0 rated ABS
• Safety Features: 4x safety hang points
• Safety Agency Ratings: ETL listed to comply with UL1480, UL2043 and CSA60065. Suitable for use in air handling spaces per NFPA 70 and NFPA 90.
• Face-Only / Back Can Options: D10-FO Face-Only Assembly; D10-BC Back Can
• Required Accessories: Electronic high pass filter
• Supplied Accessories: C-Ring supporting plate, tile support bridge rails, grille, paint mask, cut-out template, flat screwdriver
• Optional Accessories: D10-NCB New Construction Bracket
• Dimensions:
• Width: 15.197" (386 mm) bezel diameter
• Depth: 9.938 inches (252.4 mm) can depth
• Cutout Diameter: 14.125" (359 mm)
• Weight: 23.1 lbs (10.5 kg)