Telex RTS BP4000A4F Single-Channel Portable Beltpack Headset Station (4-Pin XLR, Female)

Vendor: Telex RTS
Telex RTS BP4000A4F Single-Channel Portable Beltpack Headset Station (4-Pin XLR, Female) With the Telex BP4000A4F Single-Channel Portable Beltpack Headset Station, you can stay in communication on an RTS, Audiocom, or Clear-Com intercom system. This...
$379.00
Title

Telex RTS BP4000A4F Single-Channel Portable Beltpack Headset Station (4-Pin XLR, Female)

With the Telex BP4000A4F Single-Channel Portable Beltpack Headset Station, you can stay in communication on an RTS, Audiocom, or Clear-Com intercom system. This wired beltpack station features auto-wiring scheme detection, which automatically recognizes the system you plug it into, and configures itself to be used with it.

The beltpack also features intelligent power management, so you can daisy-chain up to 40 beltpacks by using a single (optional) PS-20 power supply. A current pump circuit constantly keeps tabs on overall cable length, versus the actual current consumption, so each beltpack receives the voltage it needs.

The BP-4000 has additional features to help make it easy to integrate it into an intercom system, including guided setup and various communication controls. Connections are made by means of a female, 4-pin XLR connection.

Enhanced Talk Button Control You have the option to set your talk settings to either "always on", "always off", or "switching". A built-in blinking lamp gives you a visual indicator to incoming calls.
Remote Microphone Kill Switch Any user on the intercom can instantly mute the mics on all attached BP4000A4F beltpacks by sending an inaudible "kill signal". This feature can be overridden if needed, but is useful to have in situations where an open mic somewhere in the partyline needs to be immediately silenced.
Voice Guided Setup Rather than configure internal jumpers and switches, short voice prompts help you navigate the menu options to configure the BP4000A4F. If needed, you also have the ability to reset the beltpack to factory default settings.
Headset Compatibility The BP4000A4F has a 4-pin female XLR port that is compatible with a (separately available) 4-pin male XLR headset. Both dynamic and electret headset microphones are supported.
Features
  • Works with RTS, Audiocom, and Clear-Com
  • Auto System Detection and Configuration
  • Can Be Daisy-Chained with up to 40 Packs
  • Current Pump Circuit for Proper Power
  • Always On/Off or Switching Talk Settings
  • Blinking Incoming Call Lamp
  • Inaudible Remote Mic Kill Switch
  • Voice Guided Setup
  • 4-Pin XLR Female Connection
  • Supports Dynamic and Electret Mics
Connection 1 x XLR (4-Pin, Female)
Call Signaling Balanced Intercom Channel: 20 kHz, Send and Receive
Unbalanced Intercom Channel: 20 kHz/DC, Send and Receive
Mic Off Frequency Balanced Intercom Channel: 24 kHz, Send and Receive
Output Level Balanced Intercom Channel: 0.0 dBu, Nominal
Unbalanced Intercom Channel: 0.0 dBu, Nominal
Load Impedance Balanced: 300 Ohms
Unbalanced: 200 Ohms
Noise Balanced: < -60 dBu
Unbalanced: < -60 dBu
Total Harmonic Distortion Balanced: < 1.0%
Unbalanced: < 1.0%
Bridging Impedance Balanced: > 10 kOhms
Unbalanced: > 10 kOhms
Headphone Amplifier Maximum Output: > 140 mW into 150-Ohm Load
Frequency Response: 200 Hz to 8 kHz (±2 dB)
Audible Alert: 1 kHz
Total Harmonic Distortion: < 1.0%
Sidetone: > 20 dB Dynamic Range
Maximum Operating Current Balanced: 52 mA
Unbalanced: 45 mA
Power 18 to 33 VDC
Operating Temperature 32 to 131° F / 0 to 55° C)
Operating Humidity 5 to 95%, non-condensing
Storage Temperature -4 to 158° F / -20 to 70° C
Storage Humidity 15 to 90%, Non-Condensing
Dimensions 3.7 x 1.3 x 4.7" / 95.2 x 34.2 x 119.2 mm
3.7 x 1.6 x 4.8" / 95.2 x 39.4 x 121.6 mm (with Belt Clip and Top Panel Button)