Meyer Sound USW-210P-RMS-3, 2x10" 2-Way Active Subwoofer, RMS, M8, 3-Pin Input

Meyer Sound USW-210P-RMS-3, 2x10" 2-Way Active Subwoofer, RMS, M8, 3-Pin Input

You have limited space but require full bass response, the Meyer Sound USW-210P-RMS-3 was created to solve your problem. A compact and narrow subwoofer that stands 41.33" high and just 12" wide and deep (3.44' x 2' x 2'), the USW-210P can be mounted vertically or horizontally to a wall or ceiling. It's also possible to mount the cabinet in a free-standing vertical orientation using an optional aluminum base plate. Don't let the size fool you. The 210P can deliver 1800 watts of Class D power from a 2-channel power amp that drives a pair of 10" speakers. The bass reflex cabinet produces more output than typical 12" single driver designs while taking up less space. And, with a frequency range down to 30Hz, you'll be able to fill the room with deep, rich bass. The integrated 1800 watt 2-channel Class D amplifier has dedicated processing that provides control over crossover, driver protection, and frequency and phase response. Further resource management is provided via the RMS (Remote Monitoring System) module which provides real-time system-wide loudspeaker status. You'll have a window into the performance of amplifiers, drivers, limiting, cooling and fault alerts to help you avoid any nasty surprises. Meyer designed the 210P from premium birch with a durable black textured finish, but knowing aesthetics are important, the UWS-210P-RMS-3 is available in custom colors and finishes. Meyer Sound has been solving audio problems for over 40 years, let the USW-210P-RMS-3 solve yours today.

Meyer Sound USW-210P-RMS-3 Main Features

• Compact cabinet with small footprint and extraordinary power-to-size ratio
• 1800W peak power output with extremely low distortion
• Remote Monitor System (RMS), system management software module
• Exceptional linearity, transient reproduction, and low-frequency clarity
• Self-powered design for simplified setup and increased reliability
• Stackable and flyable in regular and cardioid arrays with splay options
• Integral pole-mount receptacle to facilitate pairing with LINA or ULTRA Series loudspeakers

• Acoustic
• Operating Frequency Range: 30–140Hz
• Frequency Response: 32–123Hz ±4dB
• Phase Response: 40–123Hz ±30°
• Linear Peak SPL: 126dB with crest factor >11.5dB (M-noise), 126dB (Pink noise), 127dB (B-noise)
• Coverage: 360° (single unit), varies with number of units and configuration
• Transducers
• Low Frequency: Two 10-inch cone drivers, nominal impedance 4Ω
• Audio Input
• Type: Differential, electronically balanced
• Maximum Common Mode Range: ±15VDC, clamped to earth for voltage transient protection
• Connectors x 4: XLR 3- or 5-pin female input with male loop output
• Input Impedance 10kΩ differential between pins 2 and 3
• Wiring
• Pin 1: Chassis/earth through 1kΩ, 1000pF, 15V clamp network to provide virtual ground lift at audio frequencies
• Pin 2: Signal + Pin 3: Signal -
• Case: Earth ground and chassis
• Nominal Input Sensitivity
• 0dBV (1V rms) continuous is typically the onset of limiting for noise and music
• Input Level
• Audio source must be capable of producing a minimum of +20dBV (10V rms) into 600Ω to produce maximum peak SPL over the operating bandwidth of the speaker
• Amplifier
• Type: 2-channel (class D) with crossover
• Total Output Power: 1800W peak
• THD, IM, TIM: < 0.02%
• Load: 4Ω per channel
• Cooling: Convection
• AC Power
• Connector: powerCON 20 input with loop output
• Automatic Voltage Selection: Automatic
• Safety Agency Rated Operating Range: 100–240VAC, 50–60Hz
• Turn-on and Turn-off Point:s 90VAC turn-on, no turn-off; internal fuse-protection above 265VAC
• Current Draw
• Idle Current: 0.27A rms (115VAC); 0.25A rms (230VAC); 0.29A rms (100VAC)
• Max Long-Term Continuous Current (>10 sec): 1.4A rms (115VAC); 0.7A rms (230VAC); 1.6A rms (100VAC)
• Burst Current (less than 1 sec): 4.5A rms (115AAC); 2.1A rms (230VAC); 4.8A rms (100VAC)
• Maximum Instantaneous Peak Current: 9.7A peak (115VAC); 4.6A peak (230VAC); 10.8A peak (100VAC)
• Inrush Current: less than 20A peak
• Physical
• Dimensions W: 12.00in (304.8mm) x H: 41.33in (1049.8mm) x D: 12.00in (304.8mm)
• Weight: 56lbs (25.40kg)
• Enclosure: Premium birch plywood, slightly textured black finish; powder-coated, stamped-steel, protective grille
• Rigging: Top and bottom mounting points with M8 threads
• RMS Network
• Type Equipped for two-conductor, twisted-pair network; reports all amplifier operating parameters to host computers