Aviom Mix320-D Personal Mixing System with Dante™ Interface
Vendor: Aviom
Available
Aviom Mix320-D Personal Mixing System with Dante™ Interface
The Aviom Mix320-D is a Personal Mixing System and professionally designed for an special use with Dante™ enabled mixing networks and consoles. This system has your back and includes everything you need for creating a personal mixing system for six performers.
The A320 Personal Mixers are getting their digital power and data over the same cable, so the user just need to do is connecting a Cat-5 cable and already ready to start using the system.
A complete monitoring system in a box, ready to use!
The Aviom Mix320-A Personal Mixing System is created and available in two versions. The standard version is perfect for users that already have in-ear monitors and/or headphones. If the user is new to personal mixing and need IEMs, then it is best to use the enhanced version of the kit with six MEE Audio M6 Pro in-ear monitors included. These single-driver IEMs include an assortment of ear tips, a 72-inch cable, and a case.
Features
- (1) D400-Dante A-Net Distributor
- (6) A320 Personal Mixers
- (6) MT-1a Mic Stand Mounts
- (7) Cat-5e cables
- (6) MEE Audio M6 Pro IEM (optional)
Product Details
The Aviom Mix320-D Personal Mixing System is making the adding of Aviom monitoring to a Dante-enabled audio network or mixing console so easy. You don't need, or it is not required, any analog input module or console card; the inputs get patched directly from your Dante network.
The Aviom Mix320-D system includes a D400-Dante A-Net Distributor that is allowing up to 32 channels to be patched from the Dante network to the personal mixing system inputs. The D400-Dante is also used for supplying DC power and A-Net digital data to the mixers. The Aviom Mix320-D system is designed with six A320 Personal Mixer for the performers, plus six MT-1a Mic Stand Mounts designed for attaching the A320 mixers to mic stands, as well as all the Cat-5e cables you'll need for connecting the products.
Intuitive Mixing
The A320 Personal Mixer gives performing and recording musicians simple, intuitive control over their monitor mixes. It features a 32-channel mix engine with 16 mono or stereo mix channels buttons and easy to use Stereo Placement controls.
Connect headphones, ear buds, or a wireless in-ear monitoring system to the Personal Mixer and you're ready to start mixing.
Distribute Power and Audio Over Cat-5
For distributing the A-Net digital data and DC power to the A320 Personal Mixers, the system includes the D400-Dante A-Net Distributor.
The D400-Dante also serves as the system's input device; it allows up to 32 channels from your Dante network to be assigned to the eight powered A-Net ports on its front panel. Stereo Link switches allow adjacent channels to be treated as a stereo pairs on the A320 Personal Mixers where they will appear on a single mix channel button.
System Options
The Mix320-D system uses a Dante network for its inputs. If you use a digital console, check out the Mix320-Y Personal Mixing System which includes a Y1 card for Yamaha® consoles for its inputs. Or, if you have an analog console or recording system, the Mix320-A Personal Mixing System is what you need. It includes the 16-channel, line-level AN-16/i Input Module as its front end.
The mixing system packages are also easy to expand when you're ready—just add more Personal Mixers and A-Net Distributors as needed.
A320 Specifications
Audio Output | 1/4" TRS stereo, headphone or line level |
---|---|
Stereo Mix Output, Headphone/Line | Tip: Audio Left; Ring: Audio Right; Sleeve: Ground |
A-Net I/O | 1 A-Net In, RJ45 connector; Supports Pro16 and Pro16e |
D/A Conversion | 44.1/48kHz, 24-bit |
Stereo Operation | Stereo Link, per channel pair; Set at the input module; Variable pan per mono channel or pan/spread per stereo channel pair |
Headphone Output | 275 mW per side into 50 Ohms (both sides driven) |
Output Impedance | 5 Ohms |
Freq. Response | 3Hz-22kHz +0.2dB/-3dB at 50 Ohms |
THD +N | < 0.003% |
Output Voltage for Personal Mixers | 24VDC, 0.5 amp Transmitted over the Cat-5e cable |
Signal to Noise (unweighted) |
-106dB (measured with zero data into all channels) |
Latency | 0.880 msec (measured from analog input to analog output) |
Pro16e A-Net | Use Cat-5e (or better) cable; Maximum 400 ft (122 m) between devices; Supports Power Over A-Net |
Cat-5 cable | Use shielded Cat-5e (or better) cable to stay below the CISPR 22 Class B, ICES-003, and FCC 47 CFR Part 15 Class B emissions limits. |
Power | 24 VDC, 0.5 amp; Power is supplied over the Cat-5 cable when connected to an Aviom A-Net Distributor |
Dimensions | 10.26" (260.6 mm) wide x 6.14" (155.95 mm) deep x 1.91" (48.51 mm) high |
Weight | 1.3 lb. (0.59 kg) |
Options | MT-1a Mic Stand Mount |
Dante Interface | 32 channels (44.1/48kHz Sample Rate) |
---|---|
Dante Primary I/O | RJ45 connector |
Dante Secondary I/O | RJ45 connector |
Dante LEDs | Network Activity (green); 1GB Network Connection Active (yellow) |
A-Net Out to Personal Mixers | Eight RJ45 connectors, powered |
A-Net Out | Pro16e A-Net; RJ45 connector, unpowered |
LEDs | Power On (red); Network Sync (green) |
Stereo Link | Two 8-position DIP switch blocks (1-16, 17-32) |
Output Voltage for Personal Mixers | 24VDC, 0.5 amp Transmitted over the Cat-5e cable |
A-Net Cables | Front Panel Connections: Shielded Cat-5e (or better) cable must be used to stay below the CISPR 22 Class B, ICES-003, and FCC 47 CFR Part 15 Class B emissions limits. Unshielded Cat-5e cable may be used on all rear panel connections |
Power Supply | Internal, IEC connector |
Input Voltage | 100-120 VAC or 200-240 VAC (with selector switch); 50-60Hz @220 W max |
AC Fuse Types | 115V range: T2.5AL/250V 230V range: T1.25AL/250V |
Dimensions | 19" (482.6 mm) wide x 7.386" (187.6 mm) deep; 2U, 3.5" (88.9 mm) high |
Weight | 12.0 lbs (5.44 kg) |