Meyer Sound MM-10XP-5 Active Subwoofer

Meyer Sound MM-10XP-5 Active Subwoofer

The Meyer Sound MM-10XP-5 miniature subwoofer is professionally designed capable of delivering an expanded low frequency intended for applications that are requiring excellent audio quality from a compact system. Carefully designed primarily as a companion to Meyer Sound's MM‑4XP miniature loudspeaker, as well as the UP‑4XP ultra-compact loudspeaker, both comes along with Intelligent DC technology, the MM‑10 is allowing the system designers for creating a full-range systems where space limitations are a concern.

The MM‑10 comes featuring an operating frequency range of 33Hz to 228Hz that comes along with a conservatively rated maximum peak SPL of 123dB. The MM‑10 bass reflex cabinet comes housing a single 10-inch driver and a single-channel power amplifier complete with onboard processing, this includes a crossover, driver protection, and frequency and phase correction. The built-in crossover is capable of accepting a full-range signals, facilitating basic daisy-chaining intended for signal distribution, which eliminates the need for external

Applications

• Background music
• Small theatres
• Portable AV systems
• Compact voice reinforcement systems

Features

• Powerful low-frequency response from a very small cabinet
• Low distortion affords exceptionally clean bass
• Adaptable to complement MM‑4XP and UP‑4XP loudspeakers
• Versions include external IntelligentDC power supply or built-in AC power for driving satellite loudspeakers

• Operating Frequency Range: 33Hz – 228Hz
• Frequency Response: 35Hz – 208Hz ±4dB
• Phase Response: 38Hz – 138Hz ±45°
• Maximum Peak SPL: 123dB
• Dynamic Range: less than 100dB
• Coverage: 360°
• Transducer
• Type: 10-inch cone driver
• Nominal Impedance: 4Ω
• Voice Coil Size: 2 inches
• Power Handling: 400W (AES)
• Audio Input
• Type: Differential, electronically balanced
• Maximum Common Mode Range: ±5VDC
• Input Impedance: 10kΩ electronically balanced
• DC Blocking: 4.8Hz high pass
• CMRR: < –60dB, typically < –72dB (200Hz – 3kHz)
• RF Filter
• Common mode: 616kHz
• Differential mode: 616kHz
• Nominal Input Sensitivity –2.0dBV (0.8V rms) continuous is typically the onset of limiting for noise and music
• Input Level
• Audio source must be capable of producing +16dBV (6.3V rms, 9.0V peak) into 600Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker
• Amplifier
• Type: Class D
• Output Power: 220W
• Total Output: 440W peak
• THD, IM, TIM < .02%
• Load Capacity: 4Ω
• Cooling: Convection
• MM-10XP Rear Panel
• Audio/Power Connector
• Phoenix 5-pin male or EN3 5-pin male (two pins for DC power, three pins for balanced audio)
• Wiring
• Pin 1: DC power negative (–)
• Pin 2: DC power positive (+)
• Pin 3: Balanced audio shield, chassis/earth
• Pin 4: Balanced audio (–)
• Pin 5: Balanced audio (+)
• Input Polarity Switch: Reverses audio input polarity between pins 4 and 5
• LED: Displays loudspeaker status
• MM-10XP DC Power
• Safety Agency Rated Operating Range: 48VDC
• Current Draw:
• Idle Current: 0.16A rms
• Max. Long-Term Continuous Current (>10 sec): 0.90A rms
• Burst Current: 2.5A rms
• Ultimate Short-Term Peak Current: 3.0A peak
• Inrush Current < 7.0A peak
• MPS-488HP IntelligentDC Power Supply Required For information and specifications for the Meyer Sound MPS-488HP IntelligentDC external power supply, refer to its datasheet