| Technology |
Laser 3-chip DLP |
| Power supply |
AC 200V-240V, 7.7A, 50/60Hz
The light output will decrease to approximately 1/2 when using the projector with
AC 100V to AC 120V [9.6A]. |
| Power consumption |
1,510 W (1,525 VA [AC200V]) (0.3 W with Standby Mode set to Eco*1,
4 W with Standby Mode set to Normal)
1,217W (Normal Mode), 972 W (Eco Mode)
Operating Temperature: 25 °C (77 °F), Altitude: 700m (2,297ft),
IEC627087: 2008 Broadcast contents, Picture mode: Standard, Dynamic contrast [2] |
| BTU value |
Max 5,159 BTU |
| DLP™ chip | Panel size |
24.4 mm (0.96 inches) diagonal (16:10 aspect ratio) |
| DLP™ chip | Display method |
DLP™ chip x 3, DLP™ projection system |
| DLP™ chip | Pixels |
6,912,000 (1920 x 1200 x 3) pixels |
| Refresh Rate |
120 Hz*2 |
| LENS |
Optional (no lens included with this model), powered zoom, powered focus lens |
| Light source |
Laser Diode (Laser class: Class 1)*Class 3R for North America. |
| Illumination life of set |
Varies depending on operation mode setting.
20,000 hours at half luminance (Normal) 24,000 hours at half luminance (Eco)
* IEC62087: 2008 Broadcast contents, Dynamic contrast [3]
(NORMAL/ECO Temperature: 30°C (86°F), Altitude 700m (2,297 ft),Dynamic
Contrast [3] Under conditions of 0.15 mg/m3 of particulate matter |
| Screen Size (Diagonal) |
1.78-25.4 m (70-1,000 in) with 16:10 aspect ratio
1.78-15.24 m (70-600 in) with the ET-D75LE8, 16:10 aspect ratio
3.05-15.24 m (120-600 in) with the ET-D75LE95, 16:10 aspect ratio |
| Brightness |
21,000 lm (Center)*3*5 / 20,000 lm (Normal)*4*5 |
| Center-to-corner uniformity |
90% |
| Contrast*3 |
20,000:1 (Full On/Full Off, Dynamic Contrast Mode: 3) |
| Resolution |
WUXGA (1920 x 1200 pixels) |
| Scanning frequency | Video/Y/C |
fH:15.73KHz fV:59.94Hz, fH:15.63KHz fV:50Hz |
| Scanning frequency | RGB |
・Resolution: 640 x 400 pixels to 1920 x 1200 pixels
・Dot clock frequency: 162MHz or less
・PIAS (Panasonic Intelligent Auto Scanning) |
| Scanning frequency | YPBPR(YCBCR) |
・Resolution: 480i/576i to 1920 x 1080 pixels
・Dot clock frequency: 148.5MHz or less
・The SYNC/HD and VD terminals do not support 3 value SYNC. |
| Scanning frequency | DVI |
・Moving image signal resolution: 480i*6/576i*6 to 1920x1080
・Still image signal resolution: 640 x 400 to 1920 x 1200 (non-interlace)
・Dot clock frequency: 25 MHz to 162 MHz |
| Scanning frequency | HDMI/DIGITAL LINK |
・Moving image signal resolution: 480i*6/576i*6 to 1920x1080
Still image signal resolution: 640 x 400 to 1920 x 1200 (non-interlace)
・Dot clock frequency: 25 MHz to 162 MHz |
| Scanning frequency | SDI |
SD-SDI signal
HD-SDI signal
3G-SDI signal |
| Optical axis shift |
Vertical (from center of screen) ±55 % (±44 % with ET-D75LE6, +68 % - +78 % with ET-D75LE95) (powered)
Horizontal (from center of screen) ±20 % (±15 % with ET-D75LE6, ±12 % with ET-D75LE95) (powered)
NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50. |
| Installation |
Ceiling/floor, front /rear, free 360-degree installation |
| Terminals | RGB 1 IN |
BNC x 5 |
| Terminals | RGB 1 IN | R, G, B |
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic |
| Terminals | RGB 1 IN | Y, PB, PR (Y, CB, CR) |
Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms |
| Terminals | RGB 1 IN | Y/C |
Y: 1.0 Vp-p (including sync signal), C: 0.286 Vp-p, 75 ohms |
| Terminals | RGB 1 IN | Video in |
BNC x 1, 1.0 Vp-p, 75 ohms |
| Terminals | RGB 2 IN |
D-sub HD 15-pin (female) x 1 |
| Terminals | RGB 2 IN | R, G, B |
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic |
| Terminals | RGB 2 IN | Y, PB, PR (Y, CB, CR) |
Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms |
| Terminals | DVI-D IN |
DVI-D 24-pin x1
Single link, DVI 1.0 compliant, HDCP compatible |
| Terminals | HDMI IN |
HDMI 19-pin x1
HDCP compatible, Deep Color compatible |
| Terminals | SDI IN 1 |
BNC x 1
SD-SDI signal SMPTE ST 259 compliant
HD-SDI signal SMPTE ST 292 compliant
3G-SDI signal SMPTE ST 424, 425-2 compliant
Dual link HD-SDI (LINK A) signal SMPTE ST 372 compliant
Dual link 3G-SDI (Link 1) signal SMPTE ST 425-3 compliant |
| Terminals | SDI IN 2 |
BNC x 1
SD-SDI signal SMPTE ST 259 compliant
HD-SDI signal SMPTE ST 292 compliant
3G-SDI signal SMPTE ST 424, 425-2 compliant
Dual link HD-SDI (LINK B) signal SMPTE ST 372 compliant
Dual link 3G-SDI (Link 2) signal SMPTE ST 425-3 compliant |
| Terminals | DIGITAL LINK |
RJ-45
HDBaseT™ compliant, HDCP compatible, Deep Color compatible |
| Terminals | 3D Sync 1 In/Out / Multi Projector Sync In |
BNC x 1, IN : TTL Hi-z OUT : TTL max10mA |
| Terminals | 3D Sync 2 Out/Multi Projector Sync Out |
BNC x 1, TTL max10mA |
| Terminals | SERIAL IN |
D-sub 9-pin x 1 for external control (RS-232C compliant) |
| Terminals | SERIAL OUT |
D-sub 9-pin x 1 for link control |
| Terminals | Remoter 1 In |
M3 jack x 1 for wired remote control |
| Terminals | Remoter 1 Out |
M3 jack x 1 for link control |
| Terminals | Remoter 2 In |
D-sub 9-pin x 1 for external control (parallel) |
| Terminals | DIGITAL LINK/LAN |
RJ-45 x 1 for network connection, 100Base-TX
PJLink™ (class 2) compatible, Art-Net compatible |
| Terminals | DC OUT 5V |
USB connector (type A) x 2 for power supply only (DC 5V, Max 2A) |
| Power cord length |
3.0 m(9 ft 10 in) |
| Cabinet materials |
Molded plastic |
| Dimensions (W x H x D) |
598 x 270 x 725 mm (23 17/32inch x 10 5/8inch x 28 17/32inch ) (not including protruding parts) |
| Weight |
*9 Approximately 49kg (108 lbs) (not including lens) |
| Operation noise |
*3 46dB |
| Operating environment |
Operating temperature: 0-50 °C (32-122 °F)*10; Operating humidity: 10-80 % (no condensation) |
FREE CHURCH DESIGNS
Call us 1-877-477-6432 or email us at sales@muzeekworld.com
USD
EUR
AUD
GBP
JPY
