Meyer Sound UPQ-D3-3, 15" 2-Way Active Speaker, 3-Pin Input

Meyer Sound UPQ-D3-3, 15" 2-Way Active Speaker, 3-Pin Input

The Meyer Sound UPQ-D3-3 is a tour tested and built to last, Meyer Sound UPQ series enclosures have delivered powerful, accurate, and detailed audio for over a decade. With a recent redesign and an added coverage option, they do that more efficiently than ever before. Benefitting from a redesign with efficiency in mind, the newest member, the UPQ-D3-3 has an onboard 2250W 2-channel Class D power amp. With reduced current draw and new generation signal processing, you'll notice a flat frequency and phase response resulting in superior transients and precise stereo imaging. Amazingly, the upgrade didn't increase the footprint, these cabinets actually weigh 13 lbs. less than the previous models, making them easier to fly and move. Meyer Sound's legendary power-to-size ratio and smooth, uniform coverage are on full display with the UPQ-D3-3. The D3 is the ultra-wide (80° x 80°) coverage model of the UPQ family. It has inherited the natural, consistent, high-frequency dispersion and gentle side roll-off that characterizes the series. This results in a gradual but expected change in what the listener hears as they move about the room, which in turn makes for more predictable system design. Designers will also appreciate being able to derive 2250W of high and mid-range coverage from a 2-way vented cabinet measuring roughly 19" x 28" x 18".

For over a decade, UPQ loudspeakers have been trusted by technicians and enjoyed by concertgoers night after night. That kind of dependability is reassuring when your job is to make sure it sounds good and everything goes as planned. The integrated 1800watt 2-channel Class D amplifier has dedicated processing that provides control over crossover, driver protection, and frequency and phase response giving you a window into system performance. The UPQ series takes the guessing out of installation and set up so you can worry about sound. Built within the same cabinet dimensions and rigging points as previous UPQ cabinets, the new models can seamlessly upgrade any current Quickfly rigged system. Equipped with an adapting AC supply that's compatible with any voltage worldwide, the UPQ-D3-3 can go where ever the road takes it. Dependability, efficiency, and proper use of power are admirable traits, the Meyer Sound UPQ-D3-3 can add them to your system today.

Meyer Sound UPQ-D3-3 Main Features

• Wide symmetrical pattern covers broad listening areas with a single loudspeaker
• Vented 2-way enclosure
• 2250W on-board Class D amplifier with sophisticated digital signal processing that provides extraordinarily flat amplitude and phase response for tonal accuracy and precise imaging
• 15" driver with neodymium magnet
• 4" compression driver
• Integral stand mount and QuickFly mounting options facilitate rigging
• Same size cabinet as previous UPQ model enclosures
• Weighs 13lbs. less than previous UPQ enclosures
• Constant‑Q horn affords uniform response throughout coverage area
• High power-to-size ratio
• Consistent and predictable performance ensures accurate system design
• Corrosion-resistant aluminum end plates with threaded M10 attachment points

• Acoustic
• Operating Frequency Range: 55Hz – 18kHz
• Frequency Response: 57Hz – 18kHz ±4dB
• Phase Response: 80Hz – 18kHz ±45°
• Linear Peak SPL4: 135dB with crest factor >17dB (M-noise), 132dB (Pink noise), 134dB (B‑noise)
• Coverage
• 80° horizontal x 80° vertical (‑6dB)
• 100° horizontal x 100° vertical (‑10dB)
• Transducers
• Low Frequency: One high‑power 15‑inch cone driver with neodymium magnet; 2Ω nominal impedance
• High Frequency: One 4‑inch diaphragm compression driver; 8Ω nominal impedance
• Audio Input
• Type: Differential, electronically balanced
• Maximum Common Mode Range: ±15VDC, clamped to earth for voltage transient protection
• Connectors: XLR 3‑pin female input with male loop output; optional 5‑pin connectors to accommodate both balanced audio and RMS signals
• Input Impedance: 10kΩ differential between pins 2 and 3
• Wiring:
• Pin 1: Chassis/earth through 220kΩ, 1000pF, 15V clamp network to provide virtual ground lift at audio frequencies
• Pin 2: Signal + Pin 3: Signal ‑
• Case: Earth ground and chassis
• Nominal Input Sensitivity: 0dBV (1.0V rms) continuous is typically the onset of limiting for noise and music
• Input Level: Audio source must be capable of producing of +20dBV (10V rms) into 600Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker.
• Amplifier
• Type: Two‑channel, Class‑D
• Total Output Power: 2250W peak
• THD, IM, TIM < 0.02%
• Cooling: Convection
• AC Power
• Connector: PowerCON 20 input with loop output
• Automatic Voltage Selection: 90–265VAC, 50–60Hz
• Safety Agency Rated Voltage Range: 100–240VAC, 50–60Hz
• Turn‑on and Turn‑off Points: 90VAC turn‑on; no turn‑off; internal fuse‑protection above 265VAC
• Current Draw
• Idle Current: 0.27A rms (115VAC); 0.25A rms (230VAC); 0.29A rms (100VAC)
• Maximum Long‑Term Continuous Current (>10 sec): 2.0A rms (115VAC); 1.0A rms (230VAC); 2.3A rms (100VAC)
• Burst Current (less than 1 sec): 3.8A rms (115VAC); 1.9A rms (230VAC); 4.4A rms (100VAC)
• Maximum Instantaneous Peak Current: 8.4A pk (115VAC); 4.1A pk (230VAC); 9.7A pk (100VAC)
• Inrush Current: < 20A peak
• RMS Network (Optional)
• Equipped with two‑conductor twisted‑pair network, reporting all operating parameters of amplifiers to system operator’s host computer.
• Physical
• Dimensions: W: 19.00in (483mm) x H: 28.15in (715mm) x D: 18.18in (462mm)
• Weight: 95lbs (43kg)
• Enclosure: Premium multi‑ply birch with slightly textured black finish
• Protective Grille: Powder‑coated, hex‑stamped steel with black mesh
• Rigging: Aluminum end plates on top and bottom with metric M10 threaded points; integral 1.5‑inch (38 mm) pole mount receptacle on bottom