Community ENT206B (Black) / ENT206W (White) ENTASYS 200 Column, 2-Way 6 LF Drivers

Vendor: Community
Community ENT206B (Black) / ENT206W (White) ENTASYS 200 Column, 2-Way 6 LF Drivers The Community ENT206B for Black and ENT206W for White, is professionally designed as an all-weather, column array loudspeaker that are housed...

Community ENT206B (Black) / ENT206W (White) ENTASYS 200 Column, 2-Way 6 LF Drivers

The Community ENT206B for Black and ENT206W for White, is professionally designed as an all-weather, column array loudspeaker that are housed in an attractive, heavy duty extruded PVC enclosure. Double the height of the smaller ENT203, the ENT206 comes providing the directional control at significantly lower frequencies than the ENT203, that comes along along with enough power for effectively covering much larger areas while still remaining unobtrusive at the same time. Ideally suited to applications such as music and speech reinforcement for reverberant hotel lobbies, houses of worship, indoor/outdoor swimming pools, assembly rooms, transit stations,  outdoor smoking areas, bowling alleys, and much more, the ENT206 is a professionally designed solid performer that belies its small size. Like the ENT203, the ENT206 is also capable to be utilized for supporting larger systems intended for delay and area fill. The ENT206 comes employing six high-power LF cone drivers and two Community CRE (Compact Ribbon Emulator) HF tweeter arrays in a two-way, single-amped configuration.

All ENTASYS 200 models are made available in standard black or white finishes, include selectable low impedance or 70/100-volt operation, a rugged pan-tilt mounting bracket and a permanently mounted safety eyebolt. The paintable enclosures that are sharing a 4-5/8-inch wide by 7-1/2-inch deep “teardrop” footprint.


  • Advanced passive crossover technology
  • Dynamic protection circuitry
  • Compact Ribbon Emulator high frequency technology for narrow, well-behaved vertical directivity control
  • All-weather construction for indoor/outdoor usage
  • Selectable low impedance or 70V/100V operation
  • Simple installation using the included pan-tilt mounting bracket
  • Tightly controlled vertical dispersion reduces harmful room reflections
  • Wide horizontal dispersion means fewer units cover a given area
  • Clean, clear and powerful sonic output without the cost of bi-amplification
  • Available in standard black or white finishes, may also be painted to match room décor
  • Loudspeaker Type: Two-way, compact column array loudspeaker, 8 Ohm or 70V/100V operation
  • Operating Range: 120 Hz to 22 kHz (-10 dB)
  • Frequency Response: 180 Hz to 20 kHz (-3 dB)
  • Max Input Ratings (8 Ohm): 150W continuous, 375W program, 35 volts RMS, 69 volts momentary peak
  • Autoformer Taps:
    • 70V: 60W, 30W, 15W, 7.5W, 3.75W
    • 100V: 60W, 30W, 15W, 7.5W
  • Sensitivity (1W/1m): 93 dB (180 Hz - 20 kHz)
  • Maximum Output: 115 dB SPL / 121 dB SPL (peak)
  • Nominal Impedance: 8 Ohms
  • Minimum Impedance: 8.1 Ohms @ 12500 Hz
  • Vertical Coverage: 20° (2 kHz to 16 kHz +/-10°) @ 13m
  • Horizontal Coverage: 140° average (1 kHz - 10 kHz +/- 20°)
  • Crossover Frequency: 5000 Hz
  • Recommended Signal Processing: 120 Hz, 24 dB/Oct high pass filter
  • Drivers:
    • LF: (6) 80mm long excursion mylar drivers
    • HF: (2) 3-element Compact Ribbon Emulators
  • Driver Protection: Dynamic protection circuitry
  • Input Connection: NL4 Speakon-type connector for low impedance operation; and 8-position terminal strip for low impedance or constant voltage operation
  • Controls: None
  • Enclosure: Extruded, high gloss paintable PVC
  • Finish: Black or white
  • Grille: Dual-layer powder coated steel, black or white finish
  • Safety Features: Built-in safety eyebolt
  • Environmental: Outdoor Direct Exposure Certified IP54W per IEC529 for UV, moisture and salt spray
  • Required Accessories: High pass filter
  • Supplied Accessories: Pan-tilt bracket accommodating zero to 22.5° down-tilt and +/- 55° panning; and ABS plastic rain cover with integrated cable inlet and 1" (25.4mm) knockout for conduit ingress
  • Optional Accessories:
    • E200-UMK universal mounting kit
    • E200-SAK stand adapter kit
  • Dimensions:
    • Height: 19.9 inches (506 mm)
    • Width: 4.62 inches (117 mm)
    • Depth: 7.47 inches (189 mm)
  • Weight (without bracket): 15 lbs (6.8 kg)